You are here: Home / Products / STONE MACHINERY / Second Hand Used Marble And Granite Electric Stone Polishing Machine

RELATED PRODUCTS

Share to:

Second Hand Used Marble And Granite Electric Stone Polishing Machine

Polishing Machine
Quantity:
  • MS-2600
  • WANLONG

Make cutting easier!

Easy operation, flexible application, superb polishing

Manual Stone Polishing Machine for Quartz in Stone Factory

 

Technical Parameters

Polishing Machine

Model

Unit

MS-2600

MS-3000

Main motor power

KW

 

4.5/5.5

4.5/5.5

Gyro radius

mm

2600

3000

Range of vertical stroke

mm

0-800

0-800

Grinding wheel diameter

mm

220

220

Max.polishing size

mm

2600x900

3000x1200

Overall dimensions(L×W×H)

mm

3500×650×1700

3800×650×1700

Water consumption

m3/h

3

3

Approximate weight

kg

850

900

The machine applies to grind and polish marble, granite, artificial panel, and sidestep stone, which is flexible in operation, stable in property, and convenient in maintenance.


There is One thing should be pay special attention: for high temperature & wear-resisting bond, high grade diamond and hard cutting material, if you mix some low grade diamond, would decrease obviously the cutting efficiency and life.
 
    Diamond grit 30/35-60/70 is mostly used in blade. When cutting high abrasive material the grit should be coarse, cutting very hard,high density Granite and crisp glass, the grit should be fine.



 

PART OF WANLONG Stone Machinery Customers(Workshop)

Manual Stone Polishing Machine for Quartz OF WANLONG Stone Machinery


Increasing concentration of diamond can longer the blade life by reducing cutting force of each diamond which reduce the wearance.But on the other hand,it reduce also the cutting efficiency and increase the cost. Theoretically, there would exist a most economic concentration.
According to different cutting requirements, the concentration of blade would range 10/50%. Small blade mostly range between 10-20%, medium diameter blade 15-40%, big size blade 25-50%.
Tips: diamond concentration means how many diamond included in segment layers,
Stipulating: diamond volume takes up 25% of diamond layer (equal to including 4.4ct/cm3 diamond), the concentration is 100%,And so on.




EXHIBITION

Customer Oriented,Honest and Highly Responsible Team  

Manual Stone Polishing Machine for Quartz Exhibition

 

As a kind of rough working, diamond saw blade cutting has a high requirement for efficiency and lifespan. The diamond should have reasonable wear and fragment shedding, while giving full play to its role. Both the premature consumption and excessive wear resistance of diamond are adverse to the cutting process. The former means that the diamond fails to function properly, which may be caused by a variety of factors: the steel is not wear-resistant or is weak to control the diamond; the cutting spend or the feeding speed is too high; the abrasive property of the stone is too strong; or the diamond has poor quality and low concentration if large fragments are found. The premature consumption of diamond is usually featured by low cutting efficiency and short lifespan.


 Therefore, in addition to adjusting the diamond and the anchoring agent, it is necessary to increase cutting speed, enlarge cutting depth and decrease feeding for reducing the crush and shedding of the diamond, as well as the wear of the anchoring agent. This method can enhance cutting efficiency and prolong the lifespan. By contrast, when the diamond has excessive wear resistance, the stone will be ground into a flat or smooth arc surface, and it is hard to produce micro crushing, which means that the anchoring agent matrix is over wear-resistant or it has too much control of the diamond; the cutting depth of the saw blade is large; the feeding is small; the processed material is hard and fine; the diamond has good quality and high concentration; the cutting depth of diamond particles into the rock is small; diamond particles are subjected to low impact and cutting force. In this case, the saw blade will have low cutting efficiency and long life macroscopically. Therefore, both the diamond and the anchoring agent should be modified. Meanwhile, it is essential to slow cutting speed, narrow cutting depth, and increase feeding, which can motivate the diamond to produce micro fractures and accelerate matrix wear, thus improve cutting efficiency.




Certification

Manual Stone Polishing Machine for Quartz Certification

FAQ

Q1: -How to order?

           -1. Please tell us what model and quantity you need.

          2. We will make a PI for you to confirm the order details.

          3. When we confirm everything, we can arrange the payment.

          4. Finally we deliver the goods within the stipulated time.

 

Q2: -When will make delivery?

          -Small machine: 7 days after payment

        -Big machine: 15~20 days after payment

 

Q3: -After-sales service

           -One year for all machines. If you find any defective accessories, we will be free to replace the new parts           for you.

 

Q4: -Payment

           -T/T

 

Q5: -Transportation

           -Transportation by logistics, ocean transportation.

 

Q6: -Are you a trader or manufacturer:

         -We are manufacturer.

 

Q7: -Can I become a distributor of OMC?

         -Yes, of course you can. 


Related Articles

content is empty!

GET IN TOUCH