You are here: Home / Products / DIAMOND TOOLS / DIAMOND SAW BLADE / Polycrystalline Diamond Saw Blade 20 Inch Diamond Saw Blade
Share to:

Polycrystalline Diamond Saw Blade 20 Inch Diamond Saw Blade

Dry cutting blade
Quantity:
  • WANLONG

CONSTRUCTION SAW BLADE 

Diamond Saw Blade for Concrete 14 Inch Diamond Saw Blade CONSTRUCTION SAW BLADE

What kind of diamond saw blade is used for cutting FRP pipes?


It is better to use ceramic dry slices, which are thin, toothless, and less abraded.

FRP pipe is also called glass fiber wound sand pipe (RPM pipe). Mainly use glass fiber and its products as reinforcement materials, use macromolecular unsaturated polyester resin, epoxy resin, etc. as basic materials, and use inorganic non-metallic particulate materials such as quartz sand and calcium carbonate as fillers as main raw materials. The standard effective length of the tube is 6m and 12m, and its production methods include fixed-length winding process, centrifugal casting process and continuous winding process. It can be classified according to the product process method, pressure grade PN and stiffness grade SN.

 


Technical Parameters

Diamond wire saw

Diameter(mm)

Segment Dimension

Born/mm

No.

105

20×1.8×7.5

16、20 22.23 25.4、50

8

115

20×1.8×8.0

16、20 22.23 25.4、50

9

125

20×2.0×8.0

16、20 22.23 25.4、50

10

150

20×2.0×7.5

16、20 22.23 25.4、50

10

180

20×2.2×8.0

16、20 22.23 25.4、50

14

200

20×2.2×8.0

16、20 22.23 25.4、50

14

230

20×2.4×8.0

16、20 22.23 25.4、50

16

250

20×2.4×8.0

16、20 22.23 25.4、50

18

300

20×2.6×8.0

16、20 22.23 25.4、50

22

350

20×2.8×8.0

16、20 22.23 25.4、50

24


Diamond saw blade is a cutting tool, which is widely used in the processing of hard and brittle materials such as concrete, refractory materials, stone, and ceramics. The diamond saw blade is mainly composed of two parts; the base body and the cutter head. The base is the main support part of the bonded cutter head, and the cutter head is the part that cuts during use. The cutter head will continue to be consumed during use, but the substrate does not. The reason why the cutter head can cut The effect is because it contains diamond, which is currently the hardest substance, and it friction cuts the processed object in the cutter head. The diamond particles are wrapped in metal inside the cutter head. 

 

Product display

Diamond Saw Blade for Concrete 14 Inch Diamond Saw Blade Product displayDiamond Saw Blade for Concrete 14 Inch Diamond Saw Blade Product displayDiamond Saw Blade for Concrete 14 Inch Diamond Saw Blade Product displayDiamond Saw Blade for Concrete 14 Inch Diamond Saw Blade Product display

 

 

What are the causes of the diamond saw blade head falling?

There are many reasons. There is a problem with the cutting machine, the saw blade is not produced without the craftsmanship, and it is caused by its own improper operation, or there is no saw blade suitable for the cutting material.


Practice has shown that for the same material, increasing the cutting depth and feed speed at the same time can increase the cutting productivity, but the abnormal wear of the saw blade is also aggravated, the service life will be reduced, and the sawing power is also increased, so the cutting is increased. cost. Generally, one-time forming and cutting can be used when cutting softer materials or strong abrasive materials; medium-diameter saw blades are mostly used for cutting boards, but also one-time cutting; and medium-hard and above granite should be cut in steps. When the depth of cut is determined, the feed rate can be converted under the condition of a certain cutting productivity. In addition, when the power is low or fine cutting is required, a lower cutting productivity should be used; when a higher power or rough cutting is used, the cutting productivity used should be higher. Table 3-2 shows the recommended cutting productivity for diamond saw blades. Table 3-2 Recommended cutting productivity of diamond circular saw blades saw blade diameter mm cutting productivity cm2/min high quartz content granite 300~600 100~300 low quartz content granite 300~600 300~600 sandstone 300~700 300~ 2000 marble 300~700 600~1500 limestone 300~700 1000~3000 marble one-time forming cutting 800~1600 1000~4000 granite cutting 800~2200 100~600 granite combination step cutting 800~1600 60~300 per piece It is pointed out that in the case of a given cutting productivity, the size of the feed rate also has a great influence on the wear of the saw blade: too high a feed rate will accelerate the wear of the cutter head binder, causing the diamond to fall off prematurely; and the feed rate When it is too low, the bond matrix wears slowly, and the diamond is not easy to be edged or polished, which leads to an increase in cutting resistance and power consumption, and cutting productivity decreases. In actual operation, the speed of cutting in, out, and out should be slow; the speed during cutting should be uniform; the saw blade should run smoothly and reduce vibration.




EXHIBITION

Customer Oriented,Honest and Highly Responsible Team  

Diamond Saw Blade for Concrete 14 Inch Diamond Saw Blade Exhibition 




Certification

Diamond Saw Blade for Concrete 14 Inch Diamond Saw Blade Certification 



Related Articles

content is empty!

GET IN TOUCH