You are here: Home / Products / DIAMOND TOOLS / DIAMOND SEGMENT / Diamond Tools for Stone Carving Universal Diamond Tools
Share to:

Diamond Tools for Stone Carving Universal Diamond Tools

Gangsaw segment
Quantity:
  • WANLONG

Make cutting easier!

Good cutting result: smooth cutting, flat surface and even size.

Diamond Gangsaw Segment for Cutting Marble Or Granite in Stone Factory 


Product  Sepcification

Gangsaw Segment

Application: Marble, Limestone, Travertine

Steel Blank Thickness (mm) Segment Size (mm) No. of segment / disc Hardness of Marble Feeding Speed (cm/h)  Lifespan (Worktable)
3.5  20x5.4/4.8x10 27~32 Soft 25~30 150
Medium Hard 20~25 100~120
Hard 15~20 60~70
3.0  20x5.0/4.5x10 27~32 Soft 25~30 150
Medium Hard 20~25 100~120
Hard 15~20 60~70
2.5  20x4.5/4.0x10 27~32 Soft 20~24 150
Medium Hard 16~20 100~120
Hard 11~16 60~70

Are diamond tools wear-resistant? Which quality is better?

The wear resistance of diamond tools is related to many factors, such as the quality of diamonds. A good diamond is not only sharp and special, but also not easy to break, so it is relatively wear-resistant; the performance of the coating must not only have a certain hardness, but also a certain toughness. To obtain such a coating, on the one hand, it has to have a good formula, on the other hand, it must master the correct operating conditions. For example, nickel-cobalt alloy plating solution is better than pure nickel plating solution, but if you do not master it, the ratio of nickel and cobalt in the plating layer cannot reach If the requirements or the ratio of the two fluctuate greatly, the coating performance will be unstable. 

Quick smooth cutting 

The blade has good sharpness and high efficiency at the process of cutting

Diamond Gangsaw Segment for Cutting Marble Or Granite in Stone Factory Quick smooth cutting

Diamond Gangsaw Segment for Cutting Marble Or Granite in Stone Factory Quick smooth cuttingDiamond Gangsaw Segment for Cutting Marble Or Granite in Stone Factory process of cutting

To make the cobalt content in the coating reach a certain proportion (usually 25-30%), it is best to use nickel and cobalt anodes at the same time, and distribute the anode current according to a certain proportion . As for the green appearance, it is caused by the high density of diamonds and the low degree of embedment. You asked a diamond tool manufacturer with a better quality and I am optimistic about Guangzhou Jinrui. As for the plating solution, there are many kinds of formulations, which are generally based on the so-called " "Watt Nickel" formula is derived based on the formula, the basic formula is: nickel sulfate 250-300 (g/L, the same below), nickel chloride 35-40 (or sodium chloride 14-18), boric acid 30-35, here On the basis, add cobalt sulfate 20-30 to form a nickel-cobalt alloy formula, reduce the content of cobalt sulfate, and add manganese sulfate 1 to form a nickel-cobalt-manganese ternary alloy formula, etc., and often add wetting agent dodecane Sodium sulphate, softener saccharin, brightener (1,4-butynediol), etc., to further improve the coating performance.



Field Operation

Diamond Gangsaw Segment for Cutting Marble Or Granite Field Operation

Diamond Gangsaw Segment for Cutting Marble Or Granite in Stone FactoryDiamond Gangsaw Segment for Cutting Marble Or Granite Field Operation  


Consistent Quality Control:  

1. Raw material  

have advanced device for diamond, powder ete inspection;

2. Finshed product

All produced product has been inspetion and approved before shipment.

3. Production

production procedure been strictly controlled by quality controlled department;

Any quality related problem that we are care and will solved for client.

 

 

EXHIBITION

Customer Oriented,Honest and Highly Responsible Team  

 Diamond Gangsaw Segment for Cutting Marble Or Granite Exhibition



Certification

Diamond Gangsaw Segment for Cutting Marble Or Granite Certification 


Company Introduction

Manufacture and use of tools make human beings have the chances to get more natural resources and create a brilliant civilization.Wanlong has dedicated to stone cutting and stone application since 1993.Today, a daily average of 100,000 pieces of Wanlong diamond tools are exported around the world. Insisting on technological innovation, we continue to create more efficient and more cost-effective diamond tools. We have developed laminated stone panel.


Related Articles

content is empty!

GET IN TOUCH