You are here: Home / Products / DIAMOND TOOLS / DIAMOND SAW BLADE / Diamond Saw Blade Sharpening Electroplated Diamond Saw Blade
Share to:

Diamond Saw Blade Sharpening Electroplated Diamond Saw Blade

Dry cutting blade
Quantity:
  • WANLONG

CONSTRUCTION SAW BLADE 

Diamond Saw Blade for Concrete 14 Inch Diamond Saw Blade CONSTRUCTION SAW BLADE

What causes the edge of the diamond saw blade?


There are two situations that affect the edge burst, the main saw blade (large saw blade burst); slot saw (bottom saw burst edge)


External reasons:

1) Listen to the sound, the machine will resonate during long-term operation. Everyone knows that the car will resonate, and the saw blade will vibrate or shake during operation. If the vibration with the machine is too large, you can adjust the contact area with the ground; If the saw blade shakes too much, you can adjust the contact surface between the drive shaft and the machine, which will cause the vibration to be transmitted. So when listening to the sound, if the machine is opening normally, you will not hear the harsh opening sound.

2) The service life of the bearing. The bearings on most domestic machines are now imported sealed (Japanese or Swiss), sometimes due to vibration or dust during long-term machine operation (because the bearings are sealed and do not require maintenance) or fixed rubber clamps outside the bearings The wear caused bearing damage. View method: You can judge by listening to the sound when starting or ending the machine


Technical Parameters

Diamond wire saw

Diameter(mm)

Segment Dimension

Born/mm

No.

105

20×1.8×7.5

16、20 22.23 25.4、50

8

115

20×1.8×8.0

16、20 22.23 25.4、50

9

125

20×2.0×8.0

16、20 22.23 25.4、50

10

150

20×2.0×7.5

16、20 22.23 25.4、50

10

180

20×2.2×8.0

16、20 22.23 25.4、50

14

200

20×2.2×8.0

16、20 22.23 25.4、50

14

230

20×2.4×8.0

16、20 22.23 25.4、50

16

250

20×2.4×8.0

16、20 22.23 25.4、50

18

300

20×2.6×8.0

16、20 22.23 25.4、50

22

350

20×2.8×8.0

16、20 22.23 25.4、50

24


3) The shaft has a certain degree of curvature during use. Including the main saw and slot saw have been calibrated at the factory, that is, the two ends are calibrated in a straight line. If there is a burst at the factory and cannot be adjusted, it proves that there may be a problem with the shaft. If something goes wrong in the use project, what causes it? Generally, workers do not understand the direction of the upper and lower saw blades when disassembling the saw blade, or do not take out the main saw hexagonal wrench in time when the saw blade is installed, which causes the shaft to deform (there is also a possibility, not many)

4) Influencing factors of the board, the resistance of the thick board (that is, the thickness is relatively thick, 2.5, 5CM) when sawing the melamine board is relatively large, and the saw blade needs to be adjusted lower to reduce the jitter;

 

Product display

Diamond Saw Blade for Concrete 14 Inch Diamond Saw Blade Product displayDiamond Saw Blade for Concrete 14 Inch Diamond Saw Blade Product displayDiamond Saw Blade for Concrete 14 Inch Diamond Saw Blade Product displayDiamond Saw Blade for Concrete 14 Inch Diamond Saw Blade Product display

 

 

EXHIBITION

Customer Oriented,Honest and Highly Responsible Team  

Diamond Saw Blade for Concrete 14 Inch Diamond Saw Blade Exhibition 


A view on the purchase of stone: Observe the surface structure of the stone with the naked eye. Generally speaking, stone with uniform fine material structure has a fine texture, which is a good product of stone; stone with coarse grain and unequal grain structure has poor appearance effect, uneven mechanical properties, and slightly worse quality. In addition, natural stone often has some fine veins and micro-cracks due to the influence of geology. The stone is most likely to break along these parts and should be removed. As for the lack of edges and corners, it will affect the appearance, so you should pay special attention when choosing.

Second quantity: measure the size of the stone, so as not to affect the splicing, or cause the pattern, pattern, and line deformation after splicing, and affect the decorative effect.

Three listens: listen to the percussive sound of the stone. Generally speaking, a stone with good quality, dense and uniform inside and no micro-cracks will have a crisp and pleasant knocking sound; on the contrary, if there are micro-cracks or fine veins inside the stone or the contact between particles becomes loose due to weathering, the knock The hit is rough.

 

Certification

Diamond Saw Blade for Concrete 14 Inch Diamond Saw Blade Certification 



Related Articles

content is empty!

GET IN TOUCH