You are here: Home / Products / DIAMOND TOOLS / ABRASIVES FOR STONE / Abrasive Stone for Marble Resin Fickert Abrasive for Granite Polishing
Share to:

Abrasive Stone for Marble Resin Fickert Abrasive for Granite Polishing

Resin Fickert
Quantity:
  • WANLONG

Resin Fickert   

Long life span, high sharpness and good polishing quality

Abrasive Stone Fine Grinding Metal Abrasives for Stone


Technical Parameters

Resin Fickert

Model

Grit

Package

T-140

120# / 180# / 240# / 320# / 400# / 600# /800# / 1000# / 1200# / 1500# / 3000#

30pcs/ctn

T-170

120# / 180# / 240# / 320# / 400# / 600# /800# / 1000# / 1200# / 1500# / 3000#

30pcs/ctn

1. Long life span, high sharpness and good polishing quality

2. Resin bonded fickert is used for fine grinding and accuracy grinding on granite slabs in automatic polishing machine

 

Product display

Long life span, high sharpness and good polishing quality


Abrasive Stone Fine Grinding Metal Abrasives for Stone Product display

Abrasive Stone Fine Grinding Metal Abrasives for Stone Product display

Marble is collectively referred to as marble internationally. With its natural and simple texture, bright and bright color, it is widely used in building interior walls. Because the marble material is relatively loose, the texture is relatively soft and the water absorption rate is relatively high. There are many joint lines, so various kinds of pollution, warping and deformation, easy to lose light and other phenomena occur during processing, transportation, installation and use, which affect the decorative effect. Therefore, the care of marble is also a required course in the nursing industry. To compare and analyze the status of marble finishes, the care methods can be divided into:


1: Refurbished grinding treatment. 

2: Local drop processing. 

3: Cleaning and protection treatment. 

4: Crystal polishing treatment. 

5: Seamless filling processing, etc. Let's first talk about the construction process of refurbishing grinding treatment and crystal polishing treatment:


Firstly, before refurbishing and sanding, make joints, waterproof, and then caulk. The purpose is to make the stone absorb as little water as possible, so as to reduce the water absorption law of the stone. (Because the water used in the renovation and polishing is absorbed by the stone, the cement underneath The water is quickly absorbed, and it is very difficult to remove the water after being absorbed by the cement, which causes the subsequent stone not to dry, and the appearance of disease such as: water spots, back alkali, white bloom, and yellow back.) When conditions permit It is best to do waterproofing again.


Application


Abrasive Stone Fine Grinding Metal Abrasives for StoneAbrasive Stone Fine Grinding Metal Abrasives for Stone

  1.  Coarse grinding: Before grinding, make the ditch and waterproof, and then fill the gap. After the waterproof effect comes out, use 50#, 150#, 300# dry grinding. 300# rear water spray grinding, 300#, 500# use diamond resin hard grinding block (do not use soft water grinding disc for rough grinding, it is prone to waves and affect the flatness). Remember that the water supply for rough grinding should not be too much. It is easy to use the spraying method. After each grinding disc is polished, use a mop to clean it. Thoroughly absorb the water. Check whether the deep cut left by the cutting edge grinding is worn off with 50# grinding discs. , Coarse grinding accounts for 45% of the overall grinding time, which is a key link to ensure the quality acceptance of the project.

    2. Fine grinding: waterproof after 800# and before grinding. After the waterproof effect comes out, use 1000#, 2000# diamond resin soft water grinding pads. Fine grinding takes up 35% of the overall grinding time. After fine grinding to 2000# The gloss can reach 50 degrees.



Finished product detection

114 degree slab glossiness black granite polished by our

Abrasive Stone Fine Grinding Metal Abrasives for Stone product detection


Consistent Quality Control:  

1. Raw material  

have advanced device for diamond, powder ete inspection;

2. Finshed product

All produced product has been inspetion and approved before shipment.

3. Production

production procedure been strictly controlled by quality controlled department;

Any quality related problem that we are care and will solved for client.

 


EXHIBITION

Customer Oriented,Honest and Highly Responsible Team  

 Abrasive Stone Fine Grinding Metal Abrasives for Stone Exhibition


SALES NETWORK

1、South Asia:India, Pakistan, Bengal, Sri lanka, etc2、South East Asia:Indonesia, Vietnam, Thailand3、Mid East:Iran, Saudi Arab, UAE, Syria, Lebanon, Israel etc

4、Africa:Egypt, Nigeria, Kenya, Ethiopia, South Africa5、America:USA, Canada, Mexico, Brazil, Venezuela, Chile, etc6、Oceania:Australia, New zealand

7、Europe:Ukraine, Poland, Bulgaria, Romania, Czech, Yugoslavia,Latvia,Lithuania,Sweden, Finland, Danmark, Spain, Greece, Turkey

 

Certification

Abrasive Stone Fine Grinding Metal Abrasives for Stone Certification 


Company Introduction

Manufacture and use of tools make human beings have the chances to get more natural resources and create a brilliant civilization.Wanlong has dedicated to stone cutting and stone application since 1993.Today, a daily average of 100,000 pieces of Wanlong diamond tools are exported around the world. Insisting on technological innovation, we continue to create more efficient and more cost-effective diamond tools. We have developed laminated stone panel.


Related Articles

content is empty!

GET IN TOUCH